ABSTRACT
The purpose of this study was to determine whether the chemical compositions of Alnico alloys had any effects on the electrical discharge machining (EDM) performance and the surface finish. This article compares the behavior of three different Alnico alloys in electrical discharge machining. The experiments were conducted under different conditions using a BP93L EDM machine (ZAP BP, Konskie, Poland), applying an additional rotary motion to the electrode. A Box-Behnken experimental design was employed to analyze the influence of three factors, i.e., the spark current, the pulse-on time, and the pulse-off time, at three levels for three Alnico alloys. The material removal rate (MRR) was calculated for the different process parameters. After the EDM, the surface roughness was studied using a Talysurf CCI Lite non-contact profiler (Taylor-Hobson, Leicester, UK). The next step of the experiments involved preparing metallographic specimens to be observed by means of scanning electron microscopy (SEM) and optical microscopy (OM). Measurements of the nanohardness were also performed. The experimental data were then analyzed using Statistica software version 10 (64-bit) to determine and graphically represent the relationships between the input and output parameters for the three Alnico alloys. The chemical compositions of the Alnico alloys affected the thickness of the white layer (higher cobalt content, lower white layer thickness) and the material removal rate. The higher the cobalt content, the thinner the white layer and the lower the material removal efficiency. Moreover, the cobalt content in Alnico alloys influenced the shape of the precipitates; these ranged from spheroidal (13% Co) to mix-shaped (21.3% Co) to flake-shaped (32.2%). The hardness of the resulting white layer was 874 HV at10 mN.
ABSTRACT
This article deals with electrical discharge machining (EDM) of an alnico alloy, focusing on how key process parameters affect the surface finish. The experiments were conducted using a BP93L EDM machine. The Box-Behnken design was employed to study the effects of three factors, i.e., spark current, pulse-on time, and pulse-off time, each at three levels, on the surface quality. A specially designed system was employed to increase the effectiveness of the machining process by imparting an additional rotary motion to the tool and an additional rotary motion to the workpiece. The aim was to efficiently remove the eroded metal particles and create a surface with smaller craters. The workpiece surface roughness was measured with a Talysurf CCI lite non-contact profiler. During this precision machining process, the arithmetical mean height (Sa) was less than 1 µm. The surface quality was examined also using scanning electron microscopy (SEM) and optical microscopy (OM). The experimental data were analyzed by means of Statistica to determine and graphically represent the relationships between the input and output parameters.
ABSTRACT
This study was undertaken to look for confirmation that heat transfer induced by abrasive water jet machining (AWJM) affects the microstructure of the material cut. The structure of S235JR carbon steel used in the experiments was reported to change locally in the jet impact zone due to the high concentration of energy generated during cutting with the abrasive water jet. It is assumed that some of the energy is transferred into the material in the form of heat. This is particularly true for materials of considerable thickness with a high thermal conductivity coefficient when cutting is performed at low speeds or with high abrasive consumption. The literature on the subject suggests that in AWJM there is little or no thermal energy effect on the microstructure of the material cut. The research described here involved the measurement of the cutting temperature with thermocouples placed at four different distances from the edge. The distances were measured using computed tomography inspection. The thermocouples used in the tests were capable of detecting temperatures of up to 100 °C. Locally, temperatures at the edge may reach much higher values. The results of the X-ray diffraction qualitative phase analysis reveal that locally the temperatures may be much higher than the eutectoid temperature. Phase changes occurred along the edge since austenite was observed. This suggests that the temperature in the jet impact zone was much higher than the eutectoid temperature. Optical microscopy was also employed to study the material microstructure. Finally, the material nanohardness was determined.
ABSTRACT
This article considers effects of local heat transfer taking place insteel cutting by abrasive water jet machining (AWJM). The influence of temperature changes during AWJM has not been investigated thoroughly. Most studies on AWJM suggest that thermal energy has little or no effect on the material cut. This study focused on the analysis of the material microstructure and indentation microhardness in the jet impact zone and the adjacent area. The structure features revealed through optical metallography and scanning microscopy suggest local temperature changes caused by the impact of the abrasive water jet against the workpiece surface. From the microscopic examinationand hardness tests, it is clear that, during the process, large amounts of energy were transferred locally. The mechanical stress produced by the water jet led to plastic deformation at and near the surface. This was accompanied by the generation and transfer of large amounts of heat resulting in a local rise in temperature to 450 °C or higher.
ABSTRACT
Measurements enabling the online monitoring of the abrasive waterjet (AWJ) cutting process are still under development. This paper presents an experimental method which can be applicable for the evaluation of the AWJ cutting quality through the measurement of forces during the cutting process. The force measuring device developed and patented by our team has been used for measurement on several metal materials. The results show the dependence of the cutting to deformation force ratio on the relative traverse speed. Thus, the force data may help with a better understanding the interaction between the abrasive jet and the material, simultaneously impacting the improvement of both the theoretical and empirical models. The advanced models could substantially improve the selection of suitable parameters for AWJ cutting, milling or turning with the desired quality of product at the end of the process. Nevertheless, it is also presented that force measurements may detect some undesired effects, e.g., not fully penetrated material and/or some product distortions. In the case of a proper designing of the measuring device, the force measurement can be applied in the online monitoring of the cutting process and its continuous control.
